Wisycom MCR42S Dual True Diversity UHF Miniature Camera Receiver - BN Band (470 to 700 MHz)

Share

The Wisycom MCR42S is a camera receiver designed for best-in-class performance. Four receivers are internally coupled by two in a real true diversity configuration. Its front end has a chain of micro-controlled-driven movable filters to allow broadband operation of up to 240 MHz with great selectivity.

A powerful low consumption DSP gives you the best of analog and digital technologies in an hybrid approach for smooth operations, high coverage, and with a Wisycom-patented PTT (push-to-talk) already integrated.

Wisycom MCR42S Receiver - Features:

• Dual true diversity in a modular stand-alone or slot-in format
• Switching bandwidth up 240 MHz in the UHF range
• DSP-based audio processing for unbeatable audio and digital outputs with integrated PTT (push-to-talk) patented technology
• 40 groups of 60 frequencies fully user programmable
• Multicompander operations
• Infrared interface for programming and transmitter synchronization
• Wisycom exclusive digital sub-carrier telemetry technology allows:
  – remote TX battery monitoring
  – tone-squelch operating
  – PTT function (An optional back-panel module is available, with the secondary intercom output)
• Easy setup and operation thru an OLED display

NOTE: This MCR42S receiver is for the BN Band (470 to 700 MHz) option and for the module only. To operate fully, either of these related adapter kits are required: BPA42PTT 'Stand Alone' Rear Panel Kit or SLK42-IKSS Superslot/Unislot Mount Adapter. For a different band option or adapter kit, please call to place a special order.

• Frequency Range: N Option (470 to 700 MHz)
• Switchable Channels: 2400 managed in 40 groups of 60 frequencies completely user customizable
• Switching-Window: Up to 232 MHz
• Frequencies: Microprocessor controlled frequency synthesizer circuit, with 25 kHz minimum step; frequencies are easily PC reprogrammed with optional UPK300E/UPKmini programmer
• Frequency Error: ± 2.5 ppm, in the rated temperature range
• Modulation: FM, with de-emphasis
• Nominal Deviation: ± 40 kHz (Max. operating dev. = ± 60 kHz)
• "A" / "B" Antenna Inputs: With SMA connectors
• Antenna Input Impedance: 50 Ω SMA type (SWR < 1:2; typ. 1:1.4)
• Sensitivity: 2 µV ( 6 dBµV), for SND/N > 58 dB; 5 µV (14 dBµV), for SND/N > 98 dB in the whole switching-window
• Amplitude Response: < 0.5 dB (RF input sig.: 6 dBµV ÷ 100 dBµV)
• Co-Channel Rejection: > 2.5 dB
• Adjacent Channel Selectivity: > 80 dB typical (for channel spacing ≥ 400 kHz)
• Spurious Receiver Rejection: > 100 dB
• IF Image Rejection: > 90 dB
• Intermod. Rejection: > 76 dB
• IIP3: > +10 dBm typical
• Spurious Emissions: < 2 nW (typical = 0.1 pW
• Noise Reduction System:
  • ENR / ENR-1.2 (Wisycom Extended-NR) , noise optimized
  • ENC / ENC-1.2 (Wisycom Extended-NC), voice optimized & with reduced pre-emphasis
  • Others, compatible with most systems, thru an internal DSP emulation of SA572, SA575 and Rms envelope compander chip set, fully user-programmable
• AF Bandwidth: 30 Hz - 20 kHz
• Frequency Response: ± 0.5 dB in the 30 Hz - 19 kHz ran
• Distortion: MCR42S: 0.3 % typical MCR42S2/S3: 0.1 % typical
• SND/D Ratio (Analog): 110 dB typical
• SND/D ratio (AES3): MCR42S: >125 dB typical MCR42S2/S3: >140 dB typical
• Audio Output: 2 audio line-outpus electronically balanced on two 3 pin mini-XLR Female connector
• Audio Output Level: Adjustable 1 dB step between (peak dev level): -30dBu [MCR42S/S2/S3] /-18dBu [MCR42] to +12dBu [MCR42/S/S2] / +18dBu [MCR42S3]
• Audio Line-Output Impededance: ± 200 Ω
• PTT Line-Output 1 & 2: Electronically balanced on a 5 pin mini-XLR Male connector
• Digital Output: Digital line-output 1 & 2 electronically balanced on 3 pin mini-XLR Male connector
• Digital Sample Rate: AES3 @ 48 kHz
• Power LEDs:
  • NEW Display: 1 multicolor RGB LEDs for the power status of the receiver
  • OLD Display: 2 multicolor RGB LEDs to easy indicate Rx1 & Rx2 power status
• RF LEDs: 2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 RF status. Always on in normal operation
• Audio LEDs: 2 multicolor RGB LEDs to easy indicates Rx1 & Rx2 audio status
• Front Buttons: Simple operation with 4 buttons to quickly monitor and setup the receiver. One touch function for a frequency scan and sync function.
• Powering:
  • External = 5 - 18 Vdc (1.5 W max)
  • Autonomous = with optional BCA 42 Battery Module (5 x IEC-LR6 1.5V size-AA alkaline or rechargeable elements)
• Power Consumption: Max 125mA @ 12V, approx. 6 hours (with battery pack BCA42)
• Battery Life: Approx. 6 hours with battery pack BCA42 (5 x IEC-LR6 1.5V size-AA alkaline)
• Temperature Range: 14 to +131° F | -10 to +55° C
• Dimensions (H x W x D):
  • Slot-In Execution: 4.5 x 2.7 x 0.7 in | 115 x 68 x 18 mm
  • Stand-Alone Execution: 5.3 x 2.7 x 0.7 in | 135 x 68 x 18 mm
• Weight: Approx. 180g